Users/posox2000/Documents/Arduino/libraries/sdc328/sd_raw.c: In function 'sd_raw_get_info': Users/posox2000/Documents/Arduino/libraries/sdc328/sd_raw.c:719: error: 'PB2' undeclared (first use in this function) Users/posox2000/Documents/Arduino/libraries/sdc328/sd_raw.c: In function 'sd_raw_write': Users/posox2000/Documents/Arduino/libraries/sdc328/sd_raw.c:471: error: 'PB2' undeclared (first use in this function) Users/posox2000/Documents/Arduino/libraries/sdc328/sd_raw.c: In function 'sd_raw_read': Users/posox2000/Documents/Arduino/libraries/sdc328/sd_raw.c:184: error: for each function it appears in.) Users/posox2000/Documents/Arduino/libraries/sdc328/sd_raw.c:184: error: (Each undeclared identifier is reported only once Users/posox2000/Documents/Arduino/libraries/sdc328/sd_raw.c:184: error: 'PB2' undeclared (first use in this function) Users/posox2000/Documents/Arduino/libraries/sdc328/sd_raw.c: In function 'sd_raw_init': I am trying to reproduce your project but compilation of your sketch giving me a lots of errors: if not writing to an SD card do something with the image data here. Void getJPEGPicture_callback( uint16_t pictureSize, uint16_t packageSize, uint16_t packageCount, byte* package ) Void getJPEGPicture_callback( uint16_t pictureSize, uint16_t packageSize,īlink(camera.InitializeSD()) // setting up the SD will result in images written to an attached SD cardīlink(camera.initial( SDCameraC328R::CT_JPEG, SDCameraC328R::PR_80圆0, SDCameraC328R::JR_640x480 )) īlink(tLightFrequency( SDCameraC328R::FT_50Hz )) īlink(camera.snapshot( SDCameraC328R::ST_COMPRESSED, 0 ) ) īlink(camera.getJPEGPicture( SDCameraC328R::PT_JPEG, PROCESS_DELAY, &getJPEGPicture_callback) ) ĭigitalWrite(ledPin, HIGH) // set the LED onĭigitalWrite(ledPin, LOW) // set the LED off every time a snapshot is taken.Īnd here is an example picture feature my very dark work area (yeah the camera isn't that great.) The module is hard-coded to write picture0001, picture0002, etc. In addition to the SD card and the camera an LED is connected to pin 2 which is what is used to report ERRORS (see SDCameraC328.h for a long list of error codes.) Note that with the arduino pro (pictured) since it operates at 3.3v you won't need to step down the voltage. For SD pin connections you might want to check out this thread. The module for interfacing to the camera was modified to work with an attached SD card. This is the library that goes along with the sketch which is a combination of the above two with some modifications The software to interface to the SD card is The software to interface to the camera module is a modified version of There is a boilerplate EXIF header added to each JPEG until I figure out how to add GPS data that I will be reading from an attached module. Letting this run in a loop (see sketch below) I was able to take 100pictures, storing them on SD without an issue. My end goal is to take pictures periodically and geotag them, putting gps cordinates in the exif section of the jpeg. I've had some recent success working with a 3.3V arduino pro, a camera module and SD memory so I thought I would share what I have so far to see if anyone has done something similar.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |